1. KZJ500 automatic numerical control bar sawing line 1. The bearing with seat used in the equipment needs to be buttered (lithium-based grease) once a month. 2. The chain needs to be refueled once a week (gear oil or oil, just apply it). 3. The feed line body motor and the discharge line body motor need to be lubricated with 220 #gear oil in the gearbox. After the new equipment runs for one month, the gear oil needs to be replaced. After that, it will be checked every three months and replaced and filled depending on the oil quality. 4. The lubricating oil level should be checked every 36 hours of operation of the air compressor and refueled as appropriate. 5. The compressor oil should be replaced every 500-800 hours of operation of the air compressor (the oil used is 68 #air compressor oil). 6. The hydraulic oil needs to be replaced once a year. 7. Routine maintenance in each shift * Check the wear of the saw blade in each shift. Special attention should be paid to check the connection of the output line body oil cylinder to ensure that the equipment is always in good working condition. * Check whether the air pressure and hydraulic pressure are normal. 2. SKZ Kangzhen Intelligent 8-character Rib Robot 1. Check the change of the clearance of each bearing, and adjust or replace it if necessary. 2. Add 3 #lithium-based lubrication to the bearing seat of the cutting mechanism once a month. 3. The sprocket in the feed bracket is lubricated with oil, and add oil to the sprocket transmission mechanism once a month. Oil model: Add SAE20 grade oil below 5 ° C in winter, and add SAE30 grade oil above 5 ° C in other seasons. The oil position can be measured by probe and observation method to submerge the lowest sprocket tooth. 4. Check the oil level and oil quality of the gear reducer gear oil every three months. The normal oil level is two-thirds of the oil window. If it is insufficient, it needs to be replenished; if the gear oil is found to have deteriorated, it needs to be replaced immediately. After one month of use of the new machine, the gear reducer lubricating oil must be completely replaced with new oil. The gear reducer uses No. 220 mechanical gear oil. 5. The compressor lubricating oil should be replaced every 500-800 hours of operation of the air compressor. 3. SKZ Kangzhen intelligent bar bending center 1. When the machine is installed, it must be placed horizontally and leveled with a horizontal ruler. The ground needs concrete hardening 2. The circuit ground wire must be well grounded. Rainproof measures must be taken for the electric control cabinet. The top of the electric control cabinet should be covered with thick plastic film or rubber 3. The foot switch should be placed in a suitable position to avoid the steel bars falling off and smashing and misoperation 4. Use the touch screen correctly. Do not tap, scrape or scratch the touch screen with hard objects 5. Different specifications of steel bars need to be replaced with corresponding bending columns. Do not use across specifications, resulting in inaccurate length, size and angle 6. After the new machine is used for one month, the gear reducer lubricating oil must be completely replaced with new oil. The gear reducer uses No. 220 mechanical gear oil. Check the oil level and oil quality of the gear reducer gear oil every three months. The normal oil level is two-thirds of the oil window; if it is found that the gear oil has deteriorated, it needs to be replaced immediately. 7. The compressor lubricating oil should be replaced every 500-800 hours of operation of the air compressor. 4. SKZ Kangzhen intelligent steel bar bending machine. 1. Check the change of the clearance of each bearing, and adjust or replace it if necessary. 2. Cut off the bearing seat of the mechanism and add 3 #lithium-based lubrication once a month. 3. The sprocket in the feed bracket is lubricated with oil. Add oil to the sprocket transmission mechanism once a month. Oil model: add SAE20 grade oil below 5 ° C in winter, and SAE30 grade oil above 5 ° C in other seasons. The oil position can be measured by probe and observation method to submerge the lowest sprocket tooth4. Check the oil level and oil quality of the gear reducer gear oil every three months (Figure 26). The normal oil level is two-thirds of the oil window. If it is insufficient, it needs to be replenished; if the gear oil is found to have deteriorated, it needs to be replaced immediately. After a month of use of the new machine, the gear reducer lubricant must be completely replaced with new oil. The gear reducer uses No. 220 mechanical gear oil 5. The compressor lubricating oil should be replaced every 500-800 hours of operation of the air compressor 5. SKZ Kangzhen intelligent steel bar shearing robot 1. Add oil to the oil hole at the cutter of the machine head once per shift; the hand pressure pump of the shearing machine head presses oil five to six times before starting each shift (fill in ordinary oil) 2. The bearing with seat used in the equipment needs to be buttered (lithium-based grease) once a month 3. The chain is refueled once a week (gear oil or oil, just apply it) 4. The lateral feed frame motor, feed line motor, discharge line motor, and trolley positioning drive motor are all deceleration motors. The gear box needs to be lubricated with 220 #gear oil. After the new equipment runs for one month, the gear oil needs to be replaced. After that, check every three months, and replace and fill depending on the oil quality. 5. Check the lubricating oil level every 36 hours of operation of the air compressor, and refuel as appropriate. 6. The compressor oil should be replaced every 500-800 hours of operation of the air compressor (the oil used is 68 #air compressor oil). 6. SKZ Kangzhen Intelligent Reinforcement Cage Roller Welding Machine 1. During the operation of the equipment, pay attention to check whether the motor is overheating. 2. During the operation of the equipment, it is strictly forbidden to cover the electrical part and keep the heat dissipation smooth. 3. After the normal operation of the machine for 1 month, re-tighten the circuit breaker, motor terminals, and electrical box terminals when the power supply is cut off. 4. 1 to 2 months. The oil volume of the hydraulic station should be checked regularly. If there is any shortage, it should be added. If there is any oil leakage, it should be repaired in time. 5. Butter all the lubricating oil nozzles once a week. 6. After the machine runs normally for 1 to 2 months, all the bolts and nuts should be re-fastened. 7. Regularly use a paint brush or a breeze hair dryer to remove the dust in the electrical cabinet every week to keep the gas cabinet clean, otherwise it may cause an accident of short circuit burning out the equipment. 7. KZS40 intelligent steel bar threading robot 1. The threading machine gear reducer is replaced with lubricating oil (gear oil or oil) once a month. 2. Lubricating oil (gear oil or oil) is not applied once per shift at the guide rail of the grinding machine. 3. Lubricating oil (gear oil or oil) is applied once per shift at the clamping place on the rough pier machine 4. Apply lubricating oil (gear oil or oil) once a shift at the push jaw guide rail 5. Refuel the chain once a week (gear oil or oil, just apply it) 6. Change the lubricating oil (gear oil or oil) once a month at the chain mobile motor gear reducer 7. Check the lubricating oil level every 36 hours of operation of the air compressor and refuel as appropriate 8. The compressor oil should be replaced every 500-800 hours of operation of the air compressor (the oil used is 68 #air compressor oil)